Generate CNC turning G-Code using Solidworks ~ Ourengineeringlabs

Generate CNC turning G-Code using Solidworks

Also Read

; Turning

; T1 NR=0.0079 - ZMIN=-5.0079 - general turning

N10 G90 G94 G18

N11 G70

N12 LIMS=2000

N13 G53 G0 X0.

; Turning Profile1

N14 T1 D1

N15 G54

N16 M8

N17 G95

N18 G97 S245 M3

N19 G0 X4.6843 Z0

N20 G96 S300 M3

N21 LIMS=2000

N22 R1=0.005 ; Cutting

N23 R3=0.005 ; Finish

N24 R4=0.005 ; Entry

N25 R5=0.005 ; Exit

N26 R6=0.005 ; Direct

N27 G0 Z0.0487

N28 X3.5974

N29 G1 X3.5174 F=R6

N30 G18

N31 G1 G42 X3.4043 Z-0.0079 F=R4

N32 Z-3.9679 F=R1

N33 X3.4843

N34 X3.485

N35 G40 X3.5982 Z-3.9113 F=R5

N36 G0 Z0.0487

N37 X3.4374

N38 G1 G42 X3.3243 Z-0.0079 F=R4

N39 Z-3.9679 F=R1

N40 X3.4443

N41 G40 X3.5574 Z-3.9113 F=R5

N42 G0 Z0.0487

N43 X3.3574

N44 G1 G42 X3.2443 Z-0.0079 F=R4

N45 Z-3.9679 F=R1

N46 X3.3643

N47 G40 X3.4774 Z-3.9113 F=R5

N48 G0 Z0.0487

N49 X3.2774

N50 G1 G42 X3.1643 Z-0.0079 F=R4

N51 Z-3.9679 F=R1

N52 X3.2843

N53 G40 X3.3974 Z-3.9113 F=R5

N54 G0 Z0.0487

N55 X3.1974

N56 G1 G42 X3.0843 Z-0.0079 F=R4

N57 Z-3.9679 F=R1

N58 X3.2043

N59 G40 X3.3174 Z-3.9113 F=R5

N60 G0 Z0.0487

N61 X3.1174

N62 G1 G42 X3.0043 Z-0.0079 F=R4

N63 Z-3.9679 F=R1

N64 X3.1243

N65 G40 X3.2374 Z-3.9113 F=R5

N66 G0 Z0.0487

N67 X3.0374

N68 G1 G42 X2.9243 Z-0.0079 F=R4

N69 Z-3.9679 F=R1

N70 X3.0443

N71 G40 X3.1574 Z-3.9113 F=R5

N72 G0 Z0.0487

N73 X2.9574

N74 G1 G42 X2.8443 Z-0.0079 F=R4

N75 Z-3.9679 F=R1

N76 X2.9643

N77 G40 X3.0774 Z-3.9113 F=R5

N78 G0 Z0.0487

N79 X2.8774

N80 G1 G42 X2.7643 Z-0.0079 F=R4

N81 Z-3.9679 F=R1

N82 X2.8843

N83 G40 X2.9974 Z-3.9113 F=R5

N84 G0 Z0.0487

N85 X2.7974

N86 G1 G42 X2.6843 Z-0.0079 F=R4

N87 Z-3.9679 F=R1

N88 X2.8043

N89 G40 X2.9174 Z-3.9113 F=R5

N90 G0 Z0.0487

N91 X2.7174

N92 G1 G42 X2.6043 Z-0.0079 F=R4

N93 Z-3.9679 F=R1

N94 X2.7243

N95 G40 X2.8374 Z-3.9113 F=R5

N96 G0 Z0.0487

N97 X2.6374

N98 G1 G42 X2.5243 Z-0.0079 F=R4

N99 Z-3.3623 F=R1

N100 G3 X2.5643 Z-3.5079 CR=0.54

N101 G1 Z-3.9679

N102 X2.6443

N103 G40 X2.7574 Z-3.9113 F=R5

N104 G0 Z0.0487

N105 X2.5574

N106 G1 G42 X2.4442 Z-0.0079 F=R4

N107 Z-3.2605 F=R1

N108 G3 X2.5643 Z-3.5069 CR=0.54

N109 G1 G40 X2.6774 Z-3.4503 F=R5

N110 G0 Z0.0487

N111 X2.4774

N112 G1 G42 X2.3642 Z-0.0079 F=R4

N113 Z-3.1948 F=R1

N114 G3 X2.4842 Z-3.3039 CR=0.54

N115 G1 G40 X2.5974 Z-3.3605 F=R5

N116 G0 Z0.0487

N117 X2.3974

N118 G1 G42 X2.2842 Z-0.0079 F=R4

N119 Z-3.1451 F=R1

N120 G3 X2.4042 Z-3.225 CR=0.54

N121 G1 G40 X2.5174 Z-3.2816 F=R5

N122 G0 Z0.0487

N123 X2.3174

N124 G1 G42 X2.2042 Z-0.0079 F=R4

N125 Z-3.1054 F=R1

N126 G3 X2.3242 Z-3.1685 CR=0.54

N127 G1 G40 X2.4374 Z-3.225 F=R5

N128 G0 Z0.0487

N129 X2.2374

N130 G1 G42 X2.1242 Z-0.0079 F=R4

N131 Z-3.0729 F=R1

N132 G3 X2.2442 Z-3.1242 CR=0.54

N133 G1 G40 X2.3574 Z-3.0676 F=R5

N134 G0 Z0.0487

N135 X2.1574

N136 G1 G42 X2.0442 Z-0.0079 F=R4

N137 Z-3.0461 F=R1

N138 G3 X2.1642 Z-3.0883 CR=0.54

N139 G1 G40 X2.2774 Z-3.0318 F=R5

N140 G0 Z0.0487

N141 X2.0774

N142 G1 G42 X1.9642 Z-0.0079 F=R4

N143 Z-3.0241 F=R1

N144 G3 X2.0842 Z-3.0589 CR=0.54

N145 G1 G40 X2.1974 Z-3.0023 F=R5

N146 G0 Z0.0487

N147 X1.9974

N148 G1 G42 X1.8842 Z-0.0079 F=R4

N149 Z-3.0063 F=R1

N150 G3 X2.0042 Z-3.0346 CR=0.54

N151 G1 G40 X2.1174 Z-2.978 F=R5

N152 G0 Z0.0487

N153 X1.9174

N154 G1 G42 X1.8042 Z-0.0079 F=R4

N155 Z-2.9921 F=R1

N156 G3 X1.9242 Z-3.0147 CR=0.54

N157 G1 G40 X2.0374 Z-2.9582 F=R5

N158 G0 Z0.0487

N159 X1.8374

N160 G1 G42 X1.7242 Z-0.0079 F=R4

N161 Z-2.9814 F=R1

N162 G3 X1.8442 Z-2.9988 CR=0.54

N163 G1 G40 X1.9574 Z-2.9422 F=R5

N164 G0 Z0.0487

N165 X1.7574

N166 G1 G42 X1.6442 Z-0.0079 F=R4

N167 Z-2.9738 F=R1

N168 G3 X1.7642 Z-2.9863 CR=0.54

N169 G1 G40 X1.8774 Z-2.9298 F=R5

N170 G0 Z0.0487

N171 X1.6774

N172 G1 G42 X1.5642 Z-0.0079 F=R4

N173 Z-1.5075 F=R1

N174 X1.5643 Z-1.5079

N175 Z-2.9694

N176 G3 X1.6842 Z-2.9772 CR=0.54

N177 G1 G40 X1.7974 Z-2.9206 F=R5

N178 G0 Z0.0487

N179 X1.5974

N180 G1 G42 X1.4842 Z-0.0079 F=R4

N181 Z-1.4627 F=R1

N182 G2 X1.5198 Z-1.472 CR=0.41

N183 G3 X1.5643 Z-1.5079 CR=0.04

N184 G1 G40 X1.6774 Z-1.5644 F=R5

N185 G0 Z0.0487

N186 X1.5174

N187 G1 G42 X1.4042 Z-0.0079 F=R4

N188 Z-1.4372 F=R1

N189 G2 X1.5198 Z-1.472 CR=0.41

N190 G1 X1.5242 Z-1.4732

N191 G40 X1.6374 Z-1.4167 F=R5

N192 G0 Z0.0487

N193 X1.4374

N194 G1 G42 X1.3242 Z-0.0079 F=R4

N195 Z-1.4043 F=R1

N196 G2 X1.4442 Z-1.4507 CR=0.41

N197 G1 G40 X1.5574 Z-1.3942 F=R5

N198 G0 Z0.0487

N199 X1.3574

N200 G1 G42 X1.2442 Z-0.0079 F=R4

N201 Z-1.3611 F=R1

N202 G2 X1.3642 Z-1.4218 CR=0.41

N203 G1 G40 X1.4774 Z-1.3652 F=R5

N204 G0 Z0.0487

N205 X1.2774

N206 G1 G42 X1.1642 Z-0.0079 F=R4

N207 Z-1.301 F=R1

N208 G2 X1.2842 Z-1.3842 CR=0.41

N209 G1 G40 X1.3974 Z-1.3277 F=R5

N210 G0 Z0.0487

N211 X1.2274

N212 G1 G42 X1.1142 Z-0.0079 F=R4

N213 Z-1.2457 F=R1

N214 G2 X1.2042 Z-1.3339 CR=0.41

N215 G1 G40 X1.3174 Z-1.2773 F=R5

N216 G0 Z0.0487

N217 X1.1911

N218 G1 X1.1774 F=R6

N219 G42 X1.0643 Z-0.0079 F=R4

N220 Z-1.1048 F=R1

N221 G2 X1.1542 Z-1.2915 CR=0.41

N222 G1 G40 X1.2674 Z-1.2349 F=R5

N223 G0 Z0.0487

N224 X1.1111

N225 G1 X1.0974 F=R6

N226 G42 X0.9843 Z-0.0079 F=R4

N227 Z-1.1048 F=R3

N228 G2 X1.4843 Z-1.5079 CR=0.45

N229 G1 Z-3.0079

N230 G3 X2.4843 Z-3.5079 CR=0.5

N231 G1 Z-4.0079

N232 X3.4843

N233 Z-5.0079

N234 G40 X3.6443 F=R6

N235 G0 X4.6843

N236 Z0

N237 G97 S245 M3

N238 M9

N239 G53 X0.

N240 G53 Z0

N241 M30

Comments

Fluid mechanics VIVA QUESTIONS and ANSWERS

1. Define density? Ans: It is defined as the ratio of mass per unit volume of the fluid. 2. Define viscosity? Ans: It is defined as the property of fluid which offers resistance to the movement of fluid over another adjacent layer of the fluid. 3. Differentiate between real fluids and ideal fluids? Ans: A fluid, which is in-compressible and is having no viscosity, is known as ideal fluid while the fluid, which possesses viscosity, is known as real fluid. 4. What is a venturimeter? Ans: It is a device which is used for measuring the rate of flow of fluid flowing through pipe. 5. What is a notch? Ans: A notch is a device used for measuring the rate of flow of a fluid through a small channel or a tank. 6. Define buoyancy? Ans: When a body is immersed in a fluid, an upward force is exerted by the fluid on the body. This upward force is equal to the weight of the fluid displaced by the body. 7. Define meta-centre? Ans: It is defined as the point about which a body...

Complete post >>

TIN SMITHY & Sheet metal

TIN SMITHY Introduction : Many engineering and house articles such as boxes, cans, funnels, ducts etc. are made from a flat sheet of metal. The process being known as tin smithy. For this the development of the article is first drawn on the sheet metal, then cut and folded, to form the required shape of the article. Allowance should be given in the drawing stage for folding and bending. This allowance depends upon the radius of the bend and thickness of the sheet metal. Sheet Metal Materials : A variety of metals are used in a sheet metal shop such as galvanized Iron, black, Iron, tin, Stainless Steel, copper and Aluminium. Hand Tools : The common hand tools used in sheet metal work are steel, try square, Wire gauge, Scriber, Ball peen hammer, Nylon Mallet, Snips Divider, Stakes, Cutting plier and Soldering Iron. Here, the details of tools that are being equipped by our workshop purpose only are presented. Wire Gauge: The thickness of sheet is referred in numbers known ...

Complete post >>

Welding VIVA question and answers

VIVA QUESTIONS : Q1: Define welding? Ans: Welding is a fabrication process that joins two or more materials, typically metals or thermoplastics, by melting and fusing them together using heat or pressure. Q2: What is the typical thickness of MS Plate used in general welding workshop experiments? Ans: The thickness of the MS (Mild Steel) plate used in general welding workshop experiments can vary depending on the specific requirements of the experiment. However, commonly used thicknesses range from 3 mm to 12 mm. Q3: What is the common job material used in welding experiments? Ans: The common job material used in welding experiments is mild steel. It is widely available, affordable, and relatively easy to work with, making it suitable for various welding applications and practice. Q4: What is the main function of an electrode in welding? Ans: The main function of an electrode in welding is to carry the electric current necessary for the welding process and to ...

Complete post >>

PLUMBING Introduction Plumbing deals with the laying of a pipeline. A craftsman may be perfectly proficient with the hammer, saw and other tools, but the faces difficulties with leaking pipes and overflowing toilets. Many people rush to a plumber on seeking a tripping pipe, but a person with a little knowledge of the sanitary system can control this problem easily, saving time and, one with help of few tools. Plumbing tools The tools used by a plumber can be classified as follows Pipe wrench Pipe vice Pipe cutter Hacksaw Dies Files and Rasps Plumb bob Pipe wrench A pipe wrench is used for holding and turning the pipes, rods and machine prts. Wrenches are classified as follows. 1.Fixed wrenches 2. Adjustable wrenches. Pipe vice A pipe vice is fitted on the work bench. This has a set of jaws to grip the pipe and prevent it from turning while cutting, threading and fitting of bends, couplings etc. The yoke vice is co...

Complete post >>

Carpentry Viva Questions

Q1: Define carpentry? Ans: Carpentry is a skilled trade that involves working with wood to construct, install, and repair structures and objects. It encompasses various tasks such as measuring, cutting, shaping, joining, and finishing wood to create functional and aesthetically pleasing products. Q2: What are the various types of wood material used in carpentry? Ans: The various types of wood materials used in carpentry include softwoods (such as pine, fir, cedar, and spruce) and hardwoods (such as oak, maple, mahogany, and walnut). Other wood materials used in carpentry can include plywood, particleboard, MDF (medium-density fiberboard), and engineered wood products like laminated veneer lumber (LVL) and oriented strand board (OSB). Q3: What is the sequence of operations in carpentry? Ans: The sequence of operations in carpentry typically involves planning and design, material selection and preparation, measuring and marking, cutting and shaping, joinery or fasteni...

Complete post >>

Welding-LAP JOINT

Ex. No : Date : LAP JOINT Aim To join the given two work pieces as a lap joint by arc welding. Material used Mild Steel plates. Tools required Welding power supply Flat file Welding rod Chipping hammer Electrode holder Wire brush Gloves and apron Earthing clamps Shield and goggles Procedure The given workpieces are thoroughly cleaned, i.e. rust, scales are removed and the edges are filed. The electrode is held in an electrode holder and ground clamp is clamped to the welding plates and the power is supplied. The workpieces are positioned on the table to form a “Lab joint”. The tag weld is done on the both the ends of joining plates to avoid the m...

Complete post >>

sheet metal rectangular tray making

Aim :- To make a rectangular tray from a given metallic sheet. Tools Required MALLET Snip Stake STEEL RULE Ball peen HAMMER Straight EDGE RIVETS Scriber Procedure The given metal sheet is smoothed using mallet. The measurements of rectangular tray (tray development drawing) is drawn on the sheet with given dimensions using the scriber and steel rule. The sheet is cut as per the marked dimensions by straight snips. Fold or bend as per the given order using mallet and stake. Bending is done as per the given dimension using the stake and mallet. Rivet the folded sheet by using the given rivets and hammer. Safety Precautions Each cut you make exposes sharp edges and creates burrs that can slice a finger. Must Use Hand gloves when cutting the sheet. Metal waste also has hazardous edges. So...

Complete post >>

SINGLE ‘V’ BUTT JOINT

Experiment No.: Date: SINGLE ‘V’ BUTT JOINT Aim: To prepare a single ‘V’ Butt Joint as per dimensions given in the sketch. Material Required: Mild Steel plates: 80mm X 40mm X 6mm = 2 Nos Mild Steel electrode ¢ 3.15 mm Equipment required: A.C. Transformer with all welding accessories like Electrode holder, cables. Tool Required: Steel rule 300mm Scriber 150mm Flat file 300mm Try square 200mm Flat Tong 450mm Chipping hammer 200mm Ball peen hammer 750mm Wire brush Welding screen Sequence of Operations: 1. Marking 2. Filing 3. Welding 4. Finishing Procedure: Take two Mild steel plates of size 80mm X 40mm X 6mm. Fix the wor...

Complete post >>

step by step procedure to draw hook 2D drawing using AutoCAD

1. Create one vertical line and two horizontal lines like shown below according to dimensions. 2.Draw the circles at intersecting points like shown below with given dimensions. 3. Draw TTR (tangent tangent Radius) circles like shown below with given radius values. 4. Trim extra elements using " TR " command the final image be shown like below. 5. Now draw another reference lines and circles using TTR(tangent tangent Radius) circle according to given dimensions. 6. Now Trim the extra elements by using "TR" command. 7. Now dimension the elements using DIM command.

Complete post >>

Sheet metal Funnel making

Making a Funnel using metallic sheet Making a Funnel using metallic sheet Aim:- To make a funnel from a given (GI)metallic sheet. Tools Required:- MALLET, SNIP, STAKE, STEEL RULE, BALL PEEN HAMMER, STRAIGHT EDGE, RIVETS, SCRIBER Procedure: The size of the given sheet metal is checked for its dimensions using a steel rule The required development of surface is being made on the white paper which is overlapped on the sheet metal. The marking is done on the sheet metal as per the development being done on the paper. Now using straight snips, unwanted materials are removed. Now fold and bend the workpiece to make the funnel shape and joint is made on the workpieces. Then using a groover, a locked grooved joint is made for about 5mm. Also, hemming is done in the bottom of the funnel. In between top face and bottom face, a butt joint is made using a solder. Finally, trimming and finishing operations are carried out. Safety Precautions:- Each cut you make exposes s...

Complete post >>

OurEngineeringLabs

Search This Blog