Skip to main content

SAFETY OPERATING PROCEDURES

Also Read

SAFETY OPERATING PROCEDURES


DO NOT use this machines unless a teacher has instructed
you in its safe use and operation and has given permission.

1. Safety glasses must be worn at all times in work areas.
4. Long and loose hair must be contained.
2. Sturdy footwear must be worn at all times in work areas.
5. Close fitting/ protective clothing must be worn.
3. Rings and jewellery must not be worn.
6. Gloves must not be worn when using this machine.

PRE-OPERATIONAL SAFETY CHECKS

1.     Check workspaces and walkways to ensure no slip/trip hazards are present.
2.     Locate and ensure you are familiar with the operation of the ON/OFF starter and E-Stop (if fitted).
3.     Ensure all guards are in place.
4.     Check that the job is clamped tight in the chuck.
5.     Remove all tools from the bed and slides of the machine.
6.     Ensure correct speed for machining process is selected.
7.     Remove the chuck key before starting the lathe.
8.     Do not try to lift chucks or face plates that are too heavy for you.
9.     Faulty equipment must not be used. Immediately report suspect machinery.

OPERATIONAL SAFETY CHECKS
1.     Never leave the lathe running unattended.
2.     Before making adjustments or measurements switch off and bring the machine to a complete standstill.
3.     Do not attempt to slow/stop the chuck or revolving work by hand.
4.     Avoid letting swarf build up on the tool or job. Stop the machine and remove it.
5.     Always remove the chuck key from the chuck.
6.     Do not store tools and parts on top of the machine.

HOUSEKEEPING

1.     Switch off the machine and reset all guards to a fully closed position.
2.     Leave the machine in a safe, clean and tidy state.

POTENTIAL HAZARDS
  • Flying objects - chuck key left in chuck                   
  • Cutting tool injury when cleaning, filing or polishing
  • Rotating machine parts - entanglement                                  
  • Metal splinters/swarf              
  • Eye injuries
Back button

Comments

RobertNelson said…
Thanks a lot for sharing this amazing knowledge with us. This site is fantastic. I always find great knowledge from it.  Life Africa TV en direct
such a lovely post very usefully information please provide few more information about this postweighbridge manufacturers
Rajesh Kumar said…
Very important points regarding safety procedures. While dealing in chemicals, acids, etc. it is very important to wear goggles, gloves and other protective as it can be life saving. Safety signs can be used to inform the workers about the safety measures. Wonderful blog with good points. Thanks a lot.
Safety Equipment Direct offers you a list of industrial products online, we are the best industrial product supplier in the USA. For more details about Safety product Price visit safetyequipmentdirect.com.
Thanks for sharing this post , Very nice blog

Marine safety equipment supplier
technofibre said…
Really nice and informative. I found this blog very useful. We offer Marine Safety Equipment service providers in UAE Marine Safety Equipment
Safety Equipment Direct provides top quality personal protective equipment and industrial products online at deep discount pricing. Our safety supplies include High Visibility Garments, Hearing Protection, Safety Glasses, Hard Hats, Hard Hat, Gloves, Winter Warming Products, Summer Cooling Products, Safety Mirrors and more. Safety Equipment Direct earns your trust by offering only the best value, top quality industrial safety product, and construction safety supplies with top-notch service before, during and after your purchases.
technofibre said…
Really nice and informative. I found this blog very useful. We offer liferaft rental services and provider in UAELiferafts Supply Fujairah for more information you can contact us +971 50 786 8975.
technofibre said…
Really nice and informative. I found this blog very useful. We offer liferaft rental services and provider in UAELiferafts Services Abu Dhabi
for more information you can contact us +971 50 786 8975.
Truly a great post. Thanks for such a great information.
Industrial PPE supplier
LED lighting manufacturer
Carol William said…
Great Post,Safety Glasses - ISG is a prime supplier of safety glasses at affordable prices. Buy top selling safety glasses at our online safety glasses store.
technofibre said…
Techno Fibre offers Inflatable Life rafts rental In Dubai UAE.Liferafts Services Fujairah For more information contact us +971 50 786 8975
Technoweigh India is a Delhi based an ISO 90001:2008 Certified organization. They are the main weighbridge producers and providers in India since 1994. They Manufacture all and each sort of weighbridge as per the most recent global standard and rules. We are occupied with assembling all sort of weighbridge like a versatile weighbridge, load cell, portable weighbridge, Highway weighbridge, electrical weighbridge, etc.

VIEW MORE :-

Weighbridge Manufacturers
Weighbridge Suppliers
Weighbridge Exporters
Portable Weighbridge
Mobile weighbridge
Digital weighbridge
Ronald I Bremer said…
If your employer or your profession requires you to wear protective safety eyewear, and you also regularly wear prescription glasses or contact lenses, you should consider a good pair of prescription safety glasses to avoid having to wear two pairs of glasses on the job, which may lead to some discomfort. Try our best prescription safety glasses for best and comfort protection.
safetscope said…
Thanks for sharing this article.
personal safety app .
Flexra Safety said…
Really Informative Blog. I really like it. Thanks for sharing it. Please keep share more.
Safety Glasses
Olivia Wilson said…
As a construction worker, my safety is always a worry. To prevent any injury, I always wear work boots, Prescription safety glasses, and gloves. I always order my safety gear from the Work Gearz website.
Tim Morkel said…
Nice Blog Thanks for sharing this post with a lot of useful information. I would like to get updates from you. Keep blogging..

Work Gloves
Such a great post and very useful content on standard operating procedure. These few safety tips will be very useful while working at the construction sites. As a reliable company in Texas, we also offer the used heavy construction equipment at the best price. For expert advice, visit our site.
Leon Dizon said…
I have a presentation subsequent week, and I’m at the search for such info about "Grip Gloves".
Look for Industrial Equipment Supplies in UAE who offer wide range of quality products at different budgets.

Recent posts

Fluid mechanics VIVA QUESTIONS and ANSWERS

1. Define density? Ans: It is defined as the ratio of mass per unit volume of the fluid. 2. Define viscosity? Ans: It is defined as the property of fluid which offers resistance to the movement of fluid over another adjacent layer of the fluid. 3. Differentiate between real fluids and ideal fluids? Ans: A fluid, which is in-compressible and is having no viscosity, is known as ideal fluid while the fluid, which possesses viscosity, is known as real fluid. 4. What is a venturimeter? Ans: It is a device which is used for measuring the rate of flow of fluid flowing through pipe. 5. What is a notch? Ans: A notch is a device used for measuring the rate of flow of a fluid through a small channel or a tank. 6. Define buoyancy? Ans: When a body is immersed in a fluid, an upward force is exerted by the fluid on the body. This upward force is equal to the weight of the fluid displaced by the body. 7. Define meta-centre? Ans: It is defined as the point about which a body

Welding VIVA question and answers

VIVA QUESTIONS : Q1: Define welding? Ans:  Welding is a fabrication process that joins two or more materials, typically metals or thermoplastics, by melting and fusing them together using heat or pressure. Q2: What is the typical thickness of MS Plate used in general welding workshop experiments? Ans:  The thickness of the MS (Mild Steel) plate used in general welding workshop experiments can vary depending on the specific requirements of the experiment. However, commonly used thicknesses range from 3 mm to 12 mm. Q3: What is the common job material used in welding experiments? Ans:  The common job material used in welding experiments is mild steel. It is widely available, affordable, and relatively easy to work with, making it suitable for various welding applications and practice. Q4: What is the main function of an electrode in welding? Ans:  The main function of an electrode in welding is to carry the electric current necessary for the welding process and to provide filler mate

sheet metal rectangular tray making

Aim :- To make a rectangular tray from a given metallic sheet. Tools Required MALLET Snip Stake STEEL RULE Ball peen HAMMER Straight EDGE RIVETS Scriber Procedure The given metal sheet is smoothed using mallet. The measurements of rectangular tray (tray development drawing) is drawn on the sheet with given dimensions using the scriber and steel rule. The sheet is cut as per the marked dimensions by straight snips. Fold or bend as per the given order using mallet and stake. Bending is done as per the given dimension using the stake and mallet. Rivet the folded sheet by using the given rivets and hammer. Safety Precautions Each cut you make exposes sharp edges and creates burrs that can slice a finger. Must Use Hand gloves when cutting the sheet. Metal waste also has hazardous edges. So

TIN SMITHY & Sheet metal

TIN SMITHY Introduction : Many engineering and house articles such as boxes, cans, funnels, ducts etc. are made from a flat sheet of metal. The process being known as tin smithy. For this the development of the article is first drawn on the sheet metal, then cut and folded, to form the required shape of the article. Allowance should be given in the drawing stage for folding and bending. This allowance depends upon the radius of the bend and thickness of the sheet metal. Sheet Metal Materials : A variety of metals are used in a sheet metal shop such as galvanized Iron, black, Iron, tin, Stainless Steel, copper and Aluminium. Hand Tools : The common hand tools used in sheet metal work are steel, try square, Wire gauge, Scriber, Ball peen hammer, Nylon Mallet, Snips Divider, Stakes, Cutting plier and Soldering Iron. Here, the details of tools that are being equipped by our workshop purpose only are presented. Wire Gauge: The thickness of sheet is referred in numbers known

Carpentry Viva Questions

Q1: Define carpentry? Ans:  Carpentry is a skilled trade that involves working with wood to construct, install, and repair structures and objects. It encompasses various tasks such as measuring, cutting, shaping, joining, and finishing wood to create functional and aesthetically pleasing products. Q2: What are the various types of wood material used in carpentry? Ans:  The various types of wood materials used in carpentry include softwoods (such as pine, fir, cedar, and spruce) and hardwoods (such as oak, maple, mahogany, and walnut). Other wood materials used in carpentry can include plywood, particleboard, MDF (medium-density fiberboard), and engineered wood products like laminated veneer lumber (LVL) and oriented strand board (OSB). Q3: What is the sequence of operations in carpentry? Ans:  The sequence of operations in carpentry typically involves planning and design, material selection and preparation, measuring and marking, cutting and shaping, joinery or fastening, assembly,

Welding-LAP JOINT

Ex. No :                                                                              Date : LAP JOINT Aim To join the given two work pieces as a lap joint by arc welding. Material used Mild Steel plates. Tools required Welding power supply  Flat file Welding rod Chipping hammer Electrode holder Wire brush Gloves and apron Earthing clamps Shield and goggles Procedure The given workpieces are thoroughly cleaned, i.e. rust, scales are removed and the  edges are filed. The electrode is held in an electrode holder and ground clamp is clamped to the  welding plates and the power is supplied. The workpieces are positioned on the table to form a “Lab joint”. The tag weld is done on the both the ends of joining plates to avoid the movement of  workpieces during welding. The welding is carried throughout the length of the workpieces on both sides by  maintaining 3mm gap between plates and the welding rod. The welded plates are allowed f

SINGLE ‘V’ BUTT JOINT

Experiment No.:                                                                                      Date: SINGLE ‘V’ BUTT JOINT Aim: To prepare a single ‘V’ Butt Joint as per dimensions given in the sketch. Material Required: Mild Steel plates: 80mm X 40mm X 6mm = 2 Nos Mild Steel electrode ¢ 3.15 mm Equipment required: A.C. Transformer with all welding accessories like Electrode holder, cables. Tool Required: Steel rule 300mm  Scriber 150mm Flat file 300mm Try square 200mm Flat Tong 450mm  Chipping hammer 200mm Ball peen hammer 750mm  Wire brush Welding screen Sequence of Operations: 1. Marking  2. Filing  3. Welding  4. Finishing Procedure: Take two Mild steel plates of size 80mm X 40mm X 6mm. Fix the work pieces one by one in bench vice and file the faces of work pieces using flat file as per dimensions. Then mark the pieces using steel rule and scriber as per drawing. Again fix the work pieces one by one in bench vice and file the pieces to

FACING, PLAIN TURNING AND STEP TURNING

Ex. No :                                                                                                          Date : FACING, PLAIN TURNING AND STEP TURNING Aim                       To perform turning, facing and chamfering on a cylindrical work piece. Material used                       Mild steel cylindrical rod. Tools required Lathe Three-jaw chuck Chuck key Vernier caliper Single-point cutting tool Procedure First loosen the jaw in the chuck key to position the work piece, and then tighten the  jaws. Fix the cutting tool in the toolpost. Switch on the lathe and move the carriage near to the workpiece. Give it a small cross  feed, and then move carriage longitudinally to the required length slowly. Bring the carriage to the original position, give a small cross feed and move carriage  longitudinally. Repeat this step until required diameter is obtained. To get smooth surface give a very small feed when the diameter is nearing

Coordinate systems in AutoCAD

World Coordinate System (WCS), User Coordinate System (UCS). There is 4 AutoCAD coordinates system you should know. Absolute coordinate system , Relative Rectangular coordinate system, Relative Polar coordinate system and Interactive system(Direct coordinate system). Absolute Coordinate system: Absolute Coordinates uses the Cartesian System to specify a position in the X, Y, and (if needed) Z axes to locate a point from the 0-X, 0-Y, and 0-Z (0,0,0) point. To locate a point using the Absolute Coordinate system, type the X-value, Y-value, and, if needed, the Z-value separated by commas (with no spaces). Syn: Enter LINE command: L [Enter] Start line at point A: 0,0 [Enter] End first line at point B: 2,2 [Enter] End of second line at point C: 2,3 [Enter] Examples shown bellow. Relative Rectangular Coordinate system: After first points entered, your next points can be entered by specifying the next coordinate compare/relative f

Sheet metal Funnel making

Making a Funnel using metallic sheet Making a Funnel using metallic sheet Aim:- To make a funnel from a given (GI)metallic sheet. Tools Required:- MALLET, SNIP, STAKE, STEEL RULE, BALL PEEN HAMMER, STRAIGHT EDGE, RIVETS, SCRIBER Procedure:  The size of the given sheet metal is checked for its dimensions using a steel rule The required development of surface is being made on the white paper which is overlapped on the sheet metal. The marking is done on the sheet metal as per the development being done on the paper. Now using straight snips, unwanted materials are removed. Now fold and bend the workpiece to make the funnel shape and joint is made on the workpieces. Then using a groover, a locked grooved joint is made for about 5mm. Also, hemming is done in the bottom of the funnel. In between top face and bottom face, a butt joint is made using a solder. Finally, trimming and finishing operations are carried out. Safety Precautions:- Each cut you make exposes sharp

Search This Blog