Find the Length and angle of the inclined line - AutoCAD fundamentals ~ Ourengineeringlabs

Find the Length and angle of the inclined line - AutoCAD fundamentals

Also Read

Here we can found two different terms are LENGTH and DISTANCE.

Measurement of Distance: The least measurement of two points or the space between two points/elements is called Distance in the above diagram 1.75 units (mm/inch) dimension is distance of the inclined line.

Measurement of Length: The length is used to measure the object entirely. In the above drawing 1.7678 units (mm/inch) dimension is length of the inclined line.

Measurement of Angle: we can take the angle measurement from the horizontal line to the required line (here the inclined line). In the above drawing the 8 degrees measurement is the angle between horizontal line to inclined line.

Hence finally:

The length of the selected inclined line is: 1.7678 units

The angle of the selected inclined line is: 8 degrees

Comments

Isometric drawings for practice in AutoCAD

What is Isometric Drawing? Isometric drawing is a method of visually representing three-dimensional objects in two dimensions. It allows for a clear and comprehensive depiction of complex structures by keeping the scale consistent and eliminating distortion. Isometric drawings use a 30-degree angle from the horizontal in all three axes (X, Y, and Z), creating a pseudo-3D effect where the height, width, and depth are equally foreshortened. Creating Isometric Drawings in AutoCAD AutoCAD provides tools and settings that make creating isometric drawings straightforward. Here’s a step-by-step guide: Step 1: Set Up Isometric Snap/Grid 1. Enable Isometric Snap/Grid: - Type `SNAP` in the command line and press `Enter`. - Type `Style` and press `Enter`. - Choose `Isometric` and press `Enter`. 2. Switch Between Isoplanes: - Type `F5` or `CTRL+E` to toggle between the top, right, and left isoplanes. Step 2: Draw Isometric Circles and Arcs 1. Isom...

Complete post >>

PLUMBING Introduction Plumbing deals with the laying of a pipeline. A craftsman may be perfectly proficient with the hammer, saw and other tools, but the faces difficulties with leaking pipes and overflowing toilets. Many people rush to a plumber on seeking a tripping pipe, but a person with a little knowledge of the sanitary system can control this problem easily, saving time and, one with help of few tools. Plumbing tools The tools used by a plumber can be classified as follows Pipe wrench Pipe vice Pipe cutter Hacksaw Dies Files and Rasps Plumb bob Pipe wrench A pipe wrench is used for holding and turning the pipes, rods and machine prts. Wrenches are classified as follows. 1.Fixed wrenches 2. Adjustable wrenches. Pipe vice A pipe vice is fitted on the work bench. This has a set of jaws to grip the pipe and prevent it from turning while cutting, threading and fitting of bends, couplings etc. The yoke vice is co...

Complete post >>

Fluid mechanics VIVA QUESTIONS and ANSWERS

1. Define density? Ans: It is defined as the ratio of mass per unit volume of the fluid. 2. Define viscosity? Ans: It is defined as the property of fluid which offers resistance to the movement of fluid over another adjacent layer of the fluid. 3. Differentiate between real fluids and ideal fluids? Ans: A fluid, which is in-compressible and is having no viscosity, is known as ideal fluid while the fluid, which possesses viscosity, is known as real fluid. 4. What is a venturimeter? Ans: It is a device which is used for measuring the rate of flow of fluid flowing through pipe. 5. What is a notch? Ans: A notch is a device used for measuring the rate of flow of a fluid through a small channel or a tank. 6. Define buoyancy? Ans: When a body is immersed in a fluid, an upward force is exerted by the fluid on the body. This upward force is equal to the weight of the fluid displaced by the body. 7. Define meta-centre? Ans: It is defined as the point about which a body...

Complete post >>

TIN SMITHY & Sheet metal

TIN SMITHY Introduction : Many engineering and house articles such as boxes, cans, funnels, ducts etc. are made from a flat sheet of metal. The process being known as tin smithy. For this the development of the article is first drawn on the sheet metal, then cut and folded, to form the required shape of the article. Allowance should be given in the drawing stage for folding and bending. This allowance depends upon the radius of the bend and thickness of the sheet metal. Sheet Metal Materials : A variety of metals are used in a sheet metal shop such as galvanized Iron, black, Iron, tin, Stainless Steel, copper and Aluminium. Hand Tools : The common hand tools used in sheet metal work are steel, try square, Wire gauge, Scriber, Ball peen hammer, Nylon Mallet, Snips Divider, Stakes, Cutting plier and Soldering Iron. Here, the details of tools that are being equipped by our workshop purpose only are presented. Wire Gauge: The thickness of sheet is referred in numbers known ...

Complete post >>

SINGLE ‘V’ BUTT JOINT

Experiment No.: Date: SINGLE ‘V’ BUTT JOINT Aim: To prepare a single ‘V’ Butt Joint as per dimensions given in the sketch. Material Required: Mild Steel plates: 80mm X 40mm X 6mm = 2 Nos Mild Steel electrode ¢ 3.15 mm Equipment required: A.C. Transformer with all welding accessories like Electrode holder, cables. Tool Required: Steel rule 300mm Scriber 150mm Flat file 300mm Try square 200mm Flat Tong 450mm Chipping hammer 200mm Ball peen hammer 750mm Wire brush Welding screen Sequence of Operations: 1. Marking 2. Filing 3. Welding 4. Finishing Procedure: Take two Mild steel plates of size 80mm X 40mm X 6mm. Fix the wor...

Complete post >>

step by step procedure to draw hook 2D drawing using AutoCAD

1. Create one vertical line and two horizontal lines like shown below according to dimensions. 2.Draw the circles at intersecting points like shown below with given dimensions. 3. Draw TTR (tangent tangent Radius) circles like shown below with given radius values. 4. Trim extra elements using " TR " command the final image be shown like below. 5. Now draw another reference lines and circles using TTR(tangent tangent Radius) circle according to given dimensions. 6. Now Trim the extra elements by using "TR" command. 7. Now dimension the elements using DIM command.

Complete post >>

SAFETY OPERATING PROCEDURES

SAFETY OPERATING PROCEDURES DO NOT use this machines unless a teacher has instructed you in its safe use and operation and has given permission. 1. Safety glasses must be worn at all times in work areas. 4. Long and loose hair must be contained. 2. Sturdy footwear must be worn at all times in work areas. 5. Close fitting/ protective clothing must be worn. 3. Rings and jewellery must not be worn. 6. Gloves must not be worn when using this machine. PRE-OPERATIONAL SAFETY CHECKS 1. Check workspaces and walkways to ensure no slip/trip hazards are present. 2. Locate and ensure you are familiar with the operation of the ON/OFF starter and E-Stop (if fitted). 3. Ensure all guards are in place. 4. Check that the job is clamped tight in the chuck. 5. Remove all tools from the b...

Complete post >>

Step by step procedure to insert 3rd Angle Projection symbol in Solidworks

Step 1: open solidworks drawing tool with default or your required sheet size. Then the object view in paper space. Step 2: 1. Click on Annotation tab and select "Note". 2. Then add the note at title block. 3. Then click on add symbol in properties manager. 4. Then click on add more symbols. Step 3: Check the symbol in symbol library categories. if you found the symbol then click on "OK" button. if you not found the 3rd angle projection in the symbol library categories then see the Step 4 in this page. Step 4: 1. Go to this file location from your computer by pasting the below in your windows explorer or browse from your computer or search "gtol.sym" and open the file location by using right clicking on the searchable file. C:\ProgramData\SOLIDWORKS\SOLIDWORKS 2019\lang\english 2. Then copy the "gtol.sym" file then paste this file in anywhere you like. here i'm pasting this file in desktop > Solidworks > pr...

Complete post >>

Coordinate systems in AutoCAD

World Coordinate System (WCS), User Coordinate System (UCS). There is 4 AutoCAD coordinates system you should know. Absolute coordinate system , Relative Rectangular coordinate system, Relative Polar coordinate system and Interactive system(Direct coordinate system). Absolute Coordinate system: Absolute Coordinates uses the Cartesian System to specify a position in the X, Y, and (if needed) Z axes to locate a point from the 0-X, 0-Y, and 0-Z (0,0,0) point. To locate a point using the Absolute Coordinate system, type the X-value, Y-value, and, if needed, the Z-value separated by commas (with no spaces). Syn: Enter LINE command: L [Enter] Start line at point A: 0,0 [Enter] End first line at point B: 2,2 [Enter] End of second line at point C: 2,3 [Enter] Examples shown bellow. Relative Rectangular Coordinate system: After first points entered, your next points can be entered by specifying the next coordinate compare/relative f...

Complete post >>

SolidWorks Practice parts

Solidworks practice parts Click here to view step by step process to make these basic shapes using solidworks Exercise 1 Exercise 2 Exercise 3 Exercise 4 Exercise 5 Exercise 6 Exercise 7 Exercise 8 Exercise 9 Exercise 10 Exercise 11 Exercise 12 Exercise 13 Exercise 14 Exercise 15 Exercise 16 Exercise 17 Exercise 18 Exercise 19 Exercise 20 Exercise 21 Exercise 22 Click here to view step by step process to make this shape using solidworks

Complete post >>

OurEngineeringLabs

Search This Blog