Step-by-Step Guide to Create an Irregular Polygon with Angles and Dimensions in AutoCAD ~ Ourengineeringlabs

Step-by-Step Guide to Create an Irregular Polygon with Angles and Dimensions in AutoCAD

Also Read

Hi there,
In this blog post, I’ll guide you step-by-step to create the irregular polygon with angles and dimensions as shown in the reference drawing using AutoCAD. It’s a great exercise to practice your line, dimension, and angle tools!

Step-by-Step Guide to Create the Irregular Polygon

Set Up Your Drawing Workspace
- Open AutoCAD and ensure you're in the Drafting & Annotation workspace.
- Use the UN command to set units:
  - Type: Decimal, Precision: 0.0.
Draw the Base Horizontal Line
- Use the Line tool (L) and draw the first line:
  - 14 units horizontally from left to right.
Draw the Angular Segments
- Use the Polar Tracking feature:
  - Enable Polar from the bottom panel.
  - Use angle increments such as 90°, 150°, 155°, 111°, etc., to match the drawing.
- Steps to Create Each Line:
  - From the end of the base line, draw subsequent lines as follows:
    - Line of 9 units at an angle of 155°.
    - Line of 9 units at an angle of 90°.
    - Line of 8 units at an angle of 121°.
    - Line of 9 units at an angle of 150°.
    - Continue this process, carefully matching each segment and its respective angle.
Use the Angle Tool to Verify Angles
- After drawing all segments, use the Angular Dimension tool to verify:
  - Select two connecting lines to display angles like 125°, 155°, 111°, 90°, etc.
- Place the angle dimensions inside or outside the shape, as shown in the reference.
Add Dimensions
- Use the Linear Dimension tool:
  - For horizontal and diagonal lengths: 14, 9, 8 units.
- Ensure all dimensions are neat and aligned for clarity.
Final Touches
- Clean up the drawing using the Trim (TR) or Erase (E) tool if needed.
- Save your drawing using the SAVEAS command and export as PDF if required.

Need Professional Drafting and 3D Modeling Services?

If you need precise 2D AutoCAD drafting or 3D CAD modeling, I’m here to help! I specialize in technical designs and detailed projects to meet your specific requirements.

Contact me for freelance work and check out my reference projects:
🔗 My Project Portfolio

Faster turnaround: First draft delivered in 1 hour, and after review and approval, the full task will proceed.

Tags:

#autocad #2ddrafting #irregularpolygon #autocadtutorial #technicaldrawing #cadexpert #engineeringdesign #draftingservices #freelancecad #cadfreelancer #autocadpractice #anglesanddimensions #cadtraining #polygoncreation #autocadprojects

Comments

FACING, PLAIN TURNING AND STEP TURNING

Ex. No : Date : FACING, PLAIN TURNING AND STEP TURNING Aim To perform turning, facing and chamfering on a cylindrical work piece. Material used Mild steel cylindrical rod. Tools required Lathe Three-jaw chuck Chuck key Vernier caliper Single-point cutting tool Procedure First loosen the jaw in the chuck key to position the work piece, and then tighten the jaws. Fix the cutting tool in the toolpost. Switch on the lath...

Complete post >>

sheet metal rectangular tray making

Aim :- To make a rectangular tray from a given metallic sheet. Tools Required MALLET Snip Stake STEEL RULE Ball peen HAMMER Straight EDGE RIVETS Scriber Procedure The given metal sheet is smoothed using mallet. The measurements of rectangular tray (tray development drawing) is drawn on the sheet with given dimensions using the scriber and steel rule. The sheet is cut as per the marked dimensions by straight snips. Fold or bend as per the given order using mallet and stake. Bending is done as per the given dimension using the stake and mallet. Rivet the folded sheet by using the given rivets and hammer. Safety Precautions Each cut you make exposes sharp edges and creates burrs that can slice a finger. Must Use Hand gloves when cutting the sheet. Metal waste also has hazardous edges. So...

Complete post >>

Carpentry Viva Questions

Q1: Define carpentry? Ans: Carpentry is a skilled trade that involves working with wood to construct, install, and repair structures and objects. It encompasses various tasks such as measuring, cutting, shaping, joining, and finishing wood to create functional and aesthetically pleasing products. Q2: What are the various types of wood material used in carpentry? Ans: The various types of wood materials used in carpentry include softwoods (such as pine, fir, cedar, and spruce) and hardwoods (such as oak, maple, mahogany, and walnut). Other wood materials used in carpentry can include plywood, particleboard, MDF (medium-density fiberboard), and engineered wood products like laminated veneer lumber (LVL) and oriented strand board (OSB). Q3: What is the sequence of operations in carpentry? Ans: The sequence of operations in carpentry typically involves planning and design, material selection and preparation, measuring and marking, cutting and shaping, joinery or fasteni...

Complete post >>

Isometric drawings for practice in AutoCAD

What is Isometric Drawing? Isometric drawing is a method of visually representing three-dimensional objects in two dimensions. It allows for a clear and comprehensive depiction of complex structures by keeping the scale consistent and eliminating distortion. Isometric drawings use a 30-degree angle from the horizontal in all three axes (X, Y, and Z), creating a pseudo-3D effect where the height, width, and depth are equally foreshortened. Creating Isometric Drawings in AutoCAD AutoCAD provides tools and settings that make creating isometric drawings straightforward. Here’s a step-by-step guide: Step 1: Set Up Isometric Snap/Grid 1. Enable Isometric Snap/Grid: - Type `SNAP` in the command line and press `Enter`. - Type `Style` and press `Enter`. - Choose `Isometric` and press `Enter`. 2. Switch Between Isoplanes: - Type `F5` or `CTRL+E` to toggle between the top, right, and left isoplanes. Step 2: Draw Isometric Circles and Arcs 1. Isom...

Complete post >>

PLUMBING Introduction Plumbing deals with the laying of a pipeline. A craftsman may be perfectly proficient with the hammer, saw and other tools, but the faces difficulties with leaking pipes and overflowing toilets. Many people rush to a plumber on seeking a tripping pipe, but a person with a little knowledge of the sanitary system can control this problem easily, saving time and, one with help of few tools. Plumbing tools The tools used by a plumber can be classified as follows Pipe wrench Pipe vice Pipe cutter Hacksaw Dies Files and Rasps Plumb bob Pipe wrench A pipe wrench is used for holding and turning the pipes, rods and machine prts. Wrenches are classified as follows. 1.Fixed wrenches 2. Adjustable wrenches. Pipe vice A pipe vice is fitted on the work bench. This has a set of jaws to grip the pipe and prevent it from turning while cutting, threading and fitting of bends, couplings etc. The yoke vice is co...

Complete post >>

Fluid mechanics VIVA QUESTIONS and ANSWERS

1. Define density? Ans: It is defined as the ratio of mass per unit volume of the fluid. 2. Define viscosity? Ans: It is defined as the property of fluid which offers resistance to the movement of fluid over another adjacent layer of the fluid. 3. Differentiate between real fluids and ideal fluids? Ans: A fluid, which is in-compressible and is having no viscosity, is known as ideal fluid while the fluid, which possesses viscosity, is known as real fluid. 4. What is a venturimeter? Ans: It is a device which is used for measuring the rate of flow of fluid flowing through pipe. 5. What is a notch? Ans: A notch is a device used for measuring the rate of flow of a fluid through a small channel or a tank. 6. Define buoyancy? Ans: When a body is immersed in a fluid, an upward force is exerted by the fluid on the body. This upward force is equal to the weight of the fluid displaced by the body. 7. Define meta-centre? Ans: It is defined as the point about which a body...

Complete post >>

Sheet metal Funnel making

Making a Funnel using metallic sheet Making a Funnel using metallic sheet Aim:- To make a funnel from a given (GI)metallic sheet. Tools Required:- MALLET, SNIP, STAKE, STEEL RULE, BALL PEEN HAMMER, STRAIGHT EDGE, RIVETS, SCRIBER Procedure: The size of the given sheet metal is checked for its dimensions using a steel rule The required development of surface is being made on the white paper which is overlapped on the sheet metal. The marking is done on the sheet metal as per the development being done on the paper. Now using straight snips, unwanted materials are removed. Now fold and bend the workpiece to make the funnel shape and joint is made on the workpieces. Then using a groover, a locked grooved joint is made for about 5mm. Also, hemming is done in the bottom of the funnel. In between top face and bottom face, a butt joint is made using a solder. Finally, trimming and finishing operations are carried out. Safety Precautions:- Each cut you make exposes s...

Complete post >>

Welding introduction

WELDING Introduction : Welding is a process of joining two similar or dissimilar metals by the application of heat with or without application of pressure and addition of filler material. The welding is extensively used in manufacturing industry, construction industry and maintenance work, replacing riveting and bolting, to a greater extent. The various welding processes are 1. Electric arc welding 2. Gas welding 3. Thermit welding 4. Resistance welding and 5. Friction welding However only electric arc welding is discussed here. In this process, the work pieces are melted along a common edge, to their melting point and then a filler metal is introduced to form the joint on solidification. The materials to be welded must be free from rust, scale oil or other impurities, so as to obtain a sound weld. Arc Welding: In arc welding, the heat required for joining the metals is obtained from an electric arc. Transformers or motor generator sets are used as arc welding ma...

Complete post >>

step by step procedure to draw hook 2D drawing using AutoCAD

1. Create one vertical line and two horizontal lines like shown below according to dimensions. 2.Draw the circles at intersecting points like shown below with given dimensions. 3. Draw TTR (tangent tangent Radius) circles like shown below with given radius values. 4. Trim extra elements using " TR " command the final image be shown like below. 5. Now draw another reference lines and circles using TTR(tangent tangent Radius) circle according to given dimensions. 6. Now Trim the extra elements by using "TR" command. 7. Now dimension the elements using DIM command.

Complete post >>

SINGLE ‘V’ BUTT JOINT

Experiment No.: Date: SINGLE ‘V’ BUTT JOINT Aim: To prepare a single ‘V’ Butt Joint as per dimensions given in the sketch. Material Required: Mild Steel plates: 80mm X 40mm X 6mm = 2 Nos Mild Steel electrode ¢ 3.15 mm Equipment required: A.C. Transformer with all welding accessories like Electrode holder, cables. Tool Required: Steel rule 300mm Scriber 150mm Flat file 300mm Try square 200mm Flat Tong 450mm Chipping hammer 200mm Ball peen hammer 750mm Wire brush Welding screen Sequence of Operations: 1. Marking 2. Filing 3. Welding 4. Finishing Procedure: Take two Mild steel plates of size 80mm X 40mm X 6mm. Fix the wor...

Complete post >>

OurEngineeringLabs

Search This Blog