Skip to main content

STRESS STRAIN CHARACTERISTICS OF MILD STEEL BAR BY UTM

Also Read

Aim:
To study the stress strain characteristics of mild steel by Universal Testing Machine
Equipment:
Universal testing machine meter rule, dividers and scale, Test specimen
Theory:
In tension test of ductile metals, the properties usually determined are yield strength, ultimate tensile strength, modulus of elasticity, percentage of elongation etc. For brittle materials only compressive strength is determined.
The tension test is normally carried out in a Universal Testing Machine (UTM). The specimen can be in the form of a rod or a plate. The dimensions of standard specimen can be known from accepted specifications.
The following properties can be determined from the stress strain curve of the material:
  1. Proportional limit: is that point on the stress strain curve at which the curve deviates from linearity, i.e. from the relation
    Stress = Young's modulus x strain
    $\sigma = E \varepsilon$
  2. Elastic limit: is the point on the stress strain curve above which plastic deformation (that is permanent deformation) starts.
  3. Yield strength: is the stress required to produce a small amount of permanent or plastic deformation.
    In some materials such as mild steel, where there is occurrence of sharp yield point on the stress -strain curve, the stress value at the lower yield point is taken as the yield strength. In some materials like tor steel which do not have a sharp yield point, the offset yield strength or proof stress is taken as the measure of the yield strength. This is the stress at which a line drawn parallel to the initial portion of the curve, offset by a specified strain, intersects.
    The offset value is usually a strain of 0.002 (0.2% strain). The value of the yield strength is of great importance in design calculations.
  4. Tensile strength or ultimate tensile strength (UTS) is the maximum load divided by the original cross sectional area of the specimen. U.T.S. corresponds to the peak or the highest stress value in the stress -strain curve.
  5. Ductility:It is usually measured as percentage elongation in length or percentage reduction in area. These measures of ductility are obtained after fracture, by keeping together the two broken parts of the specimen, and measuring the gauge length at fracture, and area of cross section at fracture.
    Percentage elongation in length = $\frac{(L_f-L_0)}{L_0}X100$
    Percentage reduction in area = $\frac{(A_f-A_0)}{A_0}X100$

    Where,
    $L_0$ and $A_0$ are initial gauge length and initial area of cross section respectively.
    $L_f$ and $A_f$ are measured gauge length at fracture and area of cross section at fracture respectively.
Procedure:
  • Mark the gauge length on the test piece (according to IS1608 ${{l}_{0}}=5.65\sqrt{{{A}_{0}}}$ )
  • Measure the diameter of the test piece at several sections by Vernier calipers and note down the mean diameter.
  • Fix the specimen firmly to the jaws of the testing machine.
  • Start the machine and gradually increase the tensile load. Collect the readings from the software assisted computer in control panel until the fracture of specimen occurs. Note down the reading where the load reaches to maximum.
  • Remove the fractured specimen from the machine and measure its diameter and the final gauge length.
  • Observe the stress strain curve for the tested specimen in software assisted computer in control panel and manually plot the graph between stress vs strain and mark the corresponding points listed below.
    a = proportionality limit
    b = elastic limit
    c = Yield point
    d = Ultimate stress
    e = Breaking stress
    A = Yield stress
  • Calculate the required objective.
Observations and Calculations:
Calculation of the diameter
Least count of Vernier Calipers =
S.No.Main Scale DivisionsVernier scale divisionsM.S.D+(V.S.D*L.C)
1
2
3
Average Value
Average diameter of the specimen (d) = _________mm
Area of the specimen ($\frac{\pi}{4}d^2$) = __________$mm^2$
Gauge length ($L_0$) = ______mm

S.No.Load(kN)Elongation $\Delta L$(mm)Stress $\frac{P}{A}$ ($\frac{N}{mm^2}$)Strain $\frac{\Delta L}{L_0}$
1
2
3
4
5
6
7
Discussion:Compare the experimental results with the theoretical values for test specimen, comment on any reason for discrepancy, comment on any instrumental/experimental errors. and area of application.
Young's modulus values of some of the metals are given below
Material E (GPA)
Chromium253
Nickel 211
Cobalt 211
Iron and steel 211
Manganese162
Titanium118
Copper 113
Silver 77
Aluminum 74
Magnesium 46
Tin 42
Lead 18
Back button

Comments

laya said…
I love this blog. Know the characteristics of mild steel,Just check out, ms Chequered Plateare the best plates. You will get a large number of customers by affording a comfortable price.

Thank you for sharing this useful information. Keep sharing this kind of information Universal Testing Machine
Anonymous said…
Great blog. Excellent information on your thank you for taking the time to share with us. Amazing insight you have on this, it's nice to find a website that details so much information. Great blog. It's very nice of you to share your knowledge through posts. I love to read stories about your experiences. They're very useful and interesting. I am excited to read the next posts. I'm so grateful for all that you've done. They're very useful and interesting. For more details you can visit Best Tmt Bar Dealers in Bangalore.

Recent posts

Isometric drawings for practice in AutoCAD

What is Isometric Drawing? Isometric drawing is a method of visually representing three-dimensional objects in two dimensions. It allows for a clear and comprehensive depiction of complex structures by keeping the scale consistent and eliminating distortion. Isometric drawings use a 30-degree angle from the horizontal in all three axes (X, Y, and Z), creating a pseudo-3D effect where the height, width, and depth are equally foreshortened. Creating Isometric Drawings in AutoCAD AutoCAD provides tools and settings that make creating isometric drawings straightforward. Here’s a step-by-step guide: Step 1: Set Up Isometric Snap/Grid 1. Enable Isometric Snap/Grid:    - Type `SNAP` in the command line and press `Enter`.    - Type `Style` and press `Enter`.    - Choose `Isometric` and press `Enter`. 2. Switch Between Isoplanes:    - Type `F5` or `CTRL+E` to toggle between the top, right, and left isoplanes. Step 2: Draw Isometric Circles and Arcs 1. Isom...

TIN SMITHY & Sheet metal

TIN SMITHY Introduction : Many engineering and house articles such as boxes, cans, funnels, ducts etc. are made from a flat sheet of metal. The process being known as tin smithy. For this the development of the article is first drawn on the sheet metal, then cut and folded, to form the required shape of the article. Allowance should be given in the drawing stage for folding and bending. This allowance depends upon the radius of the bend and thickness of the sheet metal. Sheet Metal Materials : A variety of metals are used in a sheet metal shop such as galvanized Iron, black, Iron, tin, Stainless Steel, copper and Aluminium. Hand Tools : The common hand tools used in sheet metal work are steel, try square, Wire gauge, Scriber, Ball peen hammer, Nylon Mallet, Snips Divider, Stakes, Cutting plier and Soldering Iron. Here, the details of tools that are being equipped by our workshop purpose only are presented. Wire Gauge: The thickness of sheet is referred in numbers known ...

Fluid mechanics VIVA QUESTIONS and ANSWERS

1. Define density? Ans: It is defined as the ratio of mass per unit volume of the fluid. 2. Define viscosity? Ans: It is defined as the property of fluid which offers resistance to the movement of fluid over another adjacent layer of the fluid. 3. Differentiate between real fluids and ideal fluids? Ans: A fluid, which is in-compressible and is having no viscosity, is known as ideal fluid while the fluid, which possesses viscosity, is known as real fluid. 4. What is a venturimeter? Ans: It is a device which is used for measuring the rate of flow of fluid flowing through pipe. 5. What is a notch? Ans: A notch is a device used for measuring the rate of flow of a fluid through a small channel or a tank. 6. Define buoyancy? Ans: When a body is immersed in a fluid, an upward force is exerted by the fluid on the body. This upward force is equal to the weight of the fluid displaced by the body. 7. Define meta-centre? Ans: It is defined as the point about which a body...

Welding VIVA question and answers

VIVA QUESTIONS : Q1: Define welding? Ans:  Welding is a fabrication process that joins two or more materials, typically metals or thermoplastics, by melting and fusing them together using heat or pressure. Q2: What is the typical thickness of MS Plate used in general welding workshop experiments? Ans:  The thickness of the MS (Mild Steel) plate used in general welding workshop experiments can vary depending on the specific requirements of the experiment. However, commonly used thicknesses range from 3 mm to 12 mm. Q3: What is the common job material used in welding experiments? Ans:  The common job material used in welding experiments is mild steel. It is widely available, affordable, and relatively easy to work with, making it suitable for various welding applications and practice. Q4: What is the main function of an electrode in welding? Ans:  The main function of an electrode in welding is to carry the electric current necessary for the welding process and to ...

SINGLE ‘V’ BUTT JOINT

Experiment No.:                                                                                      Date: SINGLE ‘V’ BUTT JOINT Aim: To prepare a single ‘V’ Butt Joint as per dimensions given in the sketch. Material Required: Mild Steel plates: 80mm X 40mm X 6mm = 2 Nos Mild Steel electrode ¢ 3.15 mm Equipment required: A.C. Transformer with all welding accessories like Electrode holder, cables. Tool Required: Steel rule 300mm  Scriber 150mm Flat file 300mm Try square 200mm Flat Tong 450mm  Chipping hammer 200mm Ball peen hammer 750mm  Wire brush Welding screen Sequence of Operations: 1. Marking  2. Filing  3. Welding  4. Finishing Procedure: Take two Mild steel plates of size 80mm X 40mm X 6mm. Fix the wor...

step by step procedure to draw hook 2D drawing using AutoCAD

1. Create one vertical line and two horizontal lines like shown below according to dimensions. 2.Draw the circles at intersecting points like shown below with given dimensions. 3. Draw TTR (tangent tangent Radius) circles like shown below with given radius values. 4. Trim extra elements using " TR " command the final image be shown like below. 5. Now draw another reference lines and circles using TTR(tangent tangent Radius) circle according to given dimensions. 6. Now Trim the extra elements by using "TR" command. 7. Now dimension the elements using DIM command.

MOULD WITH SPLIT PATTERN

Ex. No :                                                                                       Date : MOULD WITH SPLIT PATTERN Aim To make the mould for the given split pattern. Material required •  Moulding board •  Riser pin •  Moulding box •  Sprue pin •  Green sand •  Rammer •  Trowel •  Lifter •  Riddle •  Draw spike •  Gate cutter  •  Bellow •  Vent rod  Procedure 1. Place the moulding board on a horizontal surface. 2. The drag box is placed above the moulding board. Now one piece      of pattern is kept at  center of the drag as shown in figure. 3. The parting sand is spread before we keep the pattern. 4. Facing sand is spri...

Sheet metal Funnel making

Making a Funnel using metallic sheet Making a Funnel using metallic sheet Aim:- To make a funnel from a given (GI)metallic sheet. Tools Required:- MALLET, SNIP, STAKE, STEEL RULE, BALL PEEN HAMMER, STRAIGHT EDGE, RIVETS, SCRIBER Procedure:  The size of the given sheet metal is checked for its dimensions using a steel rule The required development of surface is being made on the white paper which is overlapped on the sheet metal. The marking is done on the sheet metal as per the development being done on the paper. Now using straight snips, unwanted materials are removed. Now fold and bend the workpiece to make the funnel shape and joint is made on the workpieces. Then using a groover, a locked grooved joint is made for about 5mm. Also, hemming is done in the bottom of the funnel. In between top face and bottom face, a butt joint is made using a solder. Finally, trimming and finishing operations are carried out. Safety Precautions:- Each cut you make exposes s...

Welding-LAP JOINT

Ex. No :                                                                              Date : LAP JOINT Aim To join the given two work pieces as a lap joint by arc welding. Material used Mild Steel plates. Tools required Welding power supply  Flat file Welding rod Chipping hammer Electrode holder Wire brush Gloves and apron Earthing clamps Shield and goggles Procedure The given workpieces are thoroughly cleaned, i.e. rust, scales are removed and the  edges are filed. The electrode is held in an electrode holder and ground clamp is clamped to the  welding plates and the power is supplied. The workpieces are positioned on the table to form a “Lab joint”. The tag weld is done on the both the ends of joining plates to avoid the m...

AutoCAD practice parts for Learners

Hi all! The below table contains some of the AutoCAD practice drawings with step by step procedure links. please visit the links to see all details of the draiwngs. Practice drawing Details Remarks Intoduction to AutoCAD Procedure steps in AutoCAD. Procedure in YOUTUBE. Download AutoCAD drawing files. You have any projects or quaries please contact us! Basic settings of drawing in AutoCAD Procedure steps in AutoCAD. Procedure in YOUTUBE. Download AutoCAD drawing files. You have any projects or quaries please contact us! Drafting settings in AutoCAD Procedure steps in AutoCAD. Procedure in YOUTUBE. Download AutoCAD drawing files. You have any projects or quaries please contact us! ...

Search This Blog